PACCAR SPN 100 FMI 2: Engine Oil Pressure Diagnosis
SPN 100 FMI 2 (FMI 2) — Engine Oil Pressure — Data Erratic, Intermittent, or Incorrect
Quick Answer
On PACCAR, SPN 100 FMI 2 is a Engine Oil Pressure fault (Data Erratic, Intermittent, or Incorrect). Prove wiring/live data first; do not parts-cannon the component.
Overview: PACCAR SPN 100 FMI 2
On PACCAR, SPN 100 FMI 2 is a Engine Oil Pressure fault (Data Erratic, Intermittent, or Incorrect). Prove wiring/live data first; do not parts-cannon the component. This guide covers symptoms, root causes, live-data checks, and misdiagnoses for PACCAR platforms.
Repair Snapshot
Time
1 - 3 Hours
Difficulty
Advanced
Parts Cost
$50 - $800
Dealer Labor
$350+
Tools Required
- PACCAR Davie
- Noregon JPRO
- Multimeter
What SPN 100 FMI 2 Means
SPN 100 FMI 2 on PACCAR means Engine Oil Pressure — Data Erratic, Intermittent, or Incorrect. Confirm Compare PID to mechanical gauge at idle and rated with PACCAR Davie / Noregon JPRO before replacing the engine oil pressure.
Symptoms Drivers Notice
- Check-engine / amber warning lamp illuminated.
- Soft power, unstable idle, or poor response when engine oil pressure data is irrational.
- Live data for engine oil pressure fails rationality vs mechanical gauge or partner sensors.
- Codes may return immediately after clearing if root cause remains.
Most Likely Root Causes
Common Misdiagnoses (Don't Waste Parts)
Why it happens:
Do this instead:
Why it happens:
Do this instead:
Why it happens:
Do this instead:
Master Tech Commentary
Mechanic's Notes
Shop tip (PACCAR): For SPN 100 FMI 2, prove Compare PID to mechanical gauge at idle and rated before quoting the Engine Oil Pressure. Common false path is replacing the sensor when the harness or reference circuit is the failure.
Step-by-Step Diagnostic Procedure
- Step 1: Connect PACCAR Davie or Noregon JPRO and record SPN 100 FMI 2 with freeze-frame load/temp.
- Step 2: Inspect harness and connector at the engine oil pressure for chafe, corrosion, and bent pins.
- Step 3: Verify 5V reference / ground / signal integrity with a multimeter where applicable.
- Step 4: Compare PID to mechanical gauge at idle and rated
- Step 5: Repair the proven fault, clear only after repair, and verify under the same conditions as freeze-frame.
Live Data & Freeze-Frame Tips
Log Engine Oil Pressure with PACCAR Davie under freeze-frame conditions. Compare PID to mechanical gauge at idle and rated. Compare to a mechanical gauge when pressure/temperature related.
When to Limp In vs Tow
Drive carefully to a shop if lamps are warning-only and power remains controllable; tow if power loss is severe.
Related Fault Codes
Frequently Asked Questions
What does PACCAR SPN 100 FMI 2 mean?
It indicates a Engine Oil Pressure fault: Data Erratic, Intermittent, or Incorrect. Confirm with live data and wiring tests before parts replacement.
Can SPN 100 cause a derate?
It can contribute to limp behavior if the ECM loses trust in critical data, especially when paired with other faults.
What tools diagnose this best?
PACCAR Davie and Noregon JPRO, plus a quality multimeter and mechanical gauges for pressure/temperature checks.
Should I clear the code first?
No. Capture freeze-frame and the full stack first. Clear only after the repair and verification.
More PACCAR codes on this system
- Paccar SPN 190 FMI 0 — Engine Speed Sensor Circuit
- PACCAR SPN 100 FMI 1 — Engine Oil Pressure Sensor
- PACCAR SPN 168 FMI 1 — Battery / Charging System Circuit
- PACCAR SPN 3510 FMI 3 — 5-Volt Sensor Supply Voltage 2
- PACCAR SPN 91 FMI 13 — Accelerator Pedal Position Sensor
- Paccar SPN 636 FMI 8 — Crankshaft Position Sensor
- Paccar SPN 1188 FMI 3 — Turbocharger Wastegate Actuator Position Sensor
- PACCAR SPN 1209 FMI 16 — Engine Exhaust Gas Pressure
Guides that go deeper
- SPN 1569 FMI 31: Engine Protection Shutdown and Safe Recovery Steps [2026 Diagnostic Guide]
SPN 1569 FMI 31 means engine protection shutdown is active—not the root fault. Read stacked codes, verify oil and coolant, then reset only after the trigger is fixed.
- Detroit DDDL Basics: Finding the Root Code Behind a Derate
Use Detroit DDDL the right way: separate root SPN/FMI faults from inducement result codes, read derate stage data, and stop replacing parts on guesses.
- How to Capture a Useful Fault Stack Before the Shop Clears Codes
How drivers and techs can capture a useful fault stack—SPNs, FMIs, freeze-frame, and counts—before anyone clears codes and erases the diagnosis.