PACCAR · SCR Outlet NOx SensorHigh

PACCAR SPN 3226 FMI 0: SCR Outlet NOx Sensor High

SPN 3226 FMI 0 (FMI 0) — Aftertreatment SCR Outlet NOx Sensor - Data Valid But High

4.8/5· 128 reviews

Quick Answer

SPN 3226 FMI 0 means PACCAR downstream NOx is higher than expected. Verify DEF quality and dosing before blaming the SCR catalyst or outlet sensor.

Overview: PACCAR SPN 3226 FMI 0

The downstream NOx sensor confirms SCR conversion efficiency by measuring NOx after the catalyst. When outlet NOx stays high, PACCAR sets SPN 3226 FMI 0 and inducement may follow.

Repair Snapshot

Time

2 - 5 Hours

Difficulty

Advanced

Parts Cost

$400 - $4,500

Dealer Labor

$700+

Tools Required

  • PACCAR Davie4
  • Jaltest
  • Multimeter

What SPN 3226 FMI 0 Means

SPN 3226 FMI 0 on PACCAR means the downstream SCR NOx sensor reads higher than expected, indicating inadequate NOx reduction or a failed sensor. Verify SCR efficiency with live data, check DEF dosing, and inspect the outlet NOx probe before replacing the catalyst.

Symptoms Drivers Notice

  • SCR efficiency below 70% in live data
  • Amber or red MIL with emissions warning
  • Downstream NOx near upstream values during steady cruise
  • SCR inducement timer active or counting down
  • Visible DEF crystallization at doser injector

Most Likely Root Causes

Inadequate DEF dosing or contaminated DEF

Common

Low DEF quality or weak dosing leaves NOx unconverted at the SCR outlet.

Failed downstream NOx sensor

Common

Sensor drift high makes a functioning SCR appear failed to the ECM.

Degraded SCR catalyst

Occasional

Thermal damage or poisoning reduces conversion even with good DEF delivery.

Common Misdiagnoses (Don't Waste Parts)

Replacing SCR catalyst without verifying DEF and dosing

Why it happens: High outlet NOx is assumed to mean dead brick.

Do this instead: Parts-cannon warning — confirm DEF at 32.5% and dosing pressure at 130–145 PSI before catalyst work.

Replacing upstream sensor when downstream is at fault

Why it happens: NOx sensors replaced as a set.

Do this instead: Compare each sensor reading independently against expected values at steady RPM.

Master Tech Commentary

Mechanic's Notes

High downstream NOx on PACCAR is either bad DEF/dosing or a failed outlet sensor — not always a dead catalyst. Log NOx during a forced regen with good DEF before authorizing SCR replacement.

Step-by-Step Diagnostic Procedure

  1. Step 1: Compare upstream vs downstream NOx in PACCAR Davie4 at 1,500 RPM — downstream should be 70–90% lower than upstream.
  2. Step 2: Test DEF concentration with refractometer — must read 32.5% urea for proper SCR conversion.
  3. Step 3: Verify DEF dosing pressure at 130–145 PSI during active dosing commands.
  4. Step 4: Inspect outlet NOx sensor for DEF crystal buildup on tip — clean or replace if contaminated.
  5. Step 5: Check for exhaust leaks between SCR outlet and downstream NOx sensor boss.

Professional service / OEM-level scan tools are recommended before clearing this fault for good.

Live Data & Freeze-Frame Tips

Log upstream NOx, downstream NOx, DEF flow rate, and SCR temp in PACCAR Davie4. Efficiency = (up - down) / up × 100. Below 70% triggers efficiency faults.

Safety Warnings

  • Outlet NOx sensor is on hot exhaust — cool below 200°F before service.
  • DEF is corrosive — protect wiring during sensor R&R.

When to Limp In vs Tow

Tow if active inducement derate limits speed below safe highway operation.

Prevention Tips for Fleets & Owner-Operators

  • Maintain DEF quality with certified fluid only.
  • Service DEF filters on schedule.
  • Fix coolant leaks before coolant poisons the SCR brick.

Related Fault Codes

SPN 3216 FMI 0 — SCR Intake NOx Sensor

Upstream NOx sensor — needed for efficiency calculation.

SPN 4364 FMI 18 — SCR NOx Efficiency

SCR NOx efficiency low stacks with outlet sensor faults.

Frequently Asked Questions

Does high downstream NOx mean bad SCR?

Not always — bad DEF, weak dosing, or a failed sensor can cause the same reading.

What is normal downstream NOx?

Typically 70–90% lower than upstream during steady cruise at operating temperature.

Can I clean a NOx sensor?

Some OEM procedures allow heating cycles — contaminated tips usually require replacement.

How do I calculate SCR efficiency?

(Upstream NOx - Downstream NOx) / Upstream NOx × 100 at steady state.

More PACCAR codes on this system

All PACCAR fault codes

Guides that go deeper